Roll on primer? • How to Paint Your Own Car, Auto Body …
2006年8月13日 · Roll a coat and walk away for an hour than roll second coat. The solvents need to have a chance to get out if you follow that you should not have a problem. Also do yourself a favor and ask the Jobber store what one they had the least problems with and buy that one. All the majors have it in one form or another.
roll or brush your primer? • How to Paint Your Own Car, Auto Body ...
2011年12月31日 · tried a cheap brush and it left too deep brush marks for the nasson 2k urathane primer I used. so I tried my $8 brush and it did a much better job. didn't notice any solvent popping. I like the evercoat stuff a lot better. for one, it doesn't need hardener. so it's cheaper too.
Roll/Brush on epoxy primer | Southern Polyurethanes Forum
2013年1月2日 · Mix it 1:1, give it some induction time, and brush or roll it on. Save your leftovers for the next day. It takes longer to cure when applied this way so give it plenty of time before the next coat goes on-hours or overnight. I've brushed repair areas many times but never tried to roll it, the better the brush quality the better the coat will be.
Learn how to paint your own car! - AutoBody101.com
2019年5月25日 · Using a 2K primer I also found that a new roller and clean tray was needed for each coat - meaning more cost and wastage. Once the primer on the roller starts to go off the roller doesn't work so well and finish is awful. I also had issues with aeration and sometimes had to re-spray the primer to get a decent finish without pinholes.
Eastwood’s roll on primer • How to Paint Your Own Car, Auto Body ...
2020年11月20日 · The 2K spray can epoxy primer will work, but it has a limited shelf life once activated so you pretty much need to use the entire can at one work session. With roll on primer, you simply mix what you need at the time. Use a short-nap disposable trim roller to apply. A small throw away brush will help.
Learn how to paint your own car! - autobody101.com
2024年11月15日 · Most of the guys now use quality automotive Epoxy Primer as the first thing applied to bare metal. It mixes 1:1 with an activator so 1 gallon gets you 2 gallons of Ready To Spray (RTS) product. Two coats is pretty much standard but you can also opt to use nothing but Epoxy Primer by applying more coats, block sanding and repeat to get the ...
Eastwood roll on primers | Southern Polyurethanes Forum
2020年7月1日 · Basic OptiFlow Epoxy and Urethane Primer Kit - Automotive Roll-On Paint - Gray
Epoxy primer over etching primer • How to Paint Your Own Car, …
2024年9月20日 · Again use either a hi quality Etching primer followed by a coat of regular primer to seal the etch Or use a good Epoxy one or the other over bare steel. Etching primers are old Tech but are hard to use in that they must be sealed with regular primers before Base and clear, Being able to tell which layer is etch and which is regular primer can ...
Roll on the SPI epoxy primer | Southern Polyurethanes Forum
2021年11月1日 · Hello all, I am restoring a 66 VW beetle in my home garage part time as a hobby. My plan is to work on one section of the body at a time, meaning do the dent repair, sand off small section at a time, apply SPI primer and body filler and etc. So the question I have is, is it ok to roll on the SPI...
favorite brand of high build primer, polyester primer?
2015年4月19日 · In my opinion polyester primer like feather fill and 2k urethane high build primers have different purposes. I use polyester primer if I am doing a large repair with a lot of bondo. That way I can finish my bondo with 80 grit sand paper. Then spray feather fill block sand it with 180 grit. Then I switch to 2k urethane high build.