Customs Definitive Carson Top '36 Ford Roadster - The Jalopy …
2011年6月19日 · David Zivot is unrelenting, “The Rick Lefeldt ’36 Ford Roadster built in 1946 in Modesto, CA, was a strong influence on the ’41-46 War Years style I was after. As Don Montgomery referred to it in Authentic Hot Rods, ‘This was a very desirable car.’ To build a traditional style car and stay true to the tradition is a distinction ...
Best 36 Ford Aluminum radiator | The H.A.M.B. - The Jalopy Journal
2013年3月6日 · Best 36 Ford Aluminum radiator Discussion in ' The Hokey Ass Message Board ' started by 26 FlatRod , Mar 6, 2013 . Joined: Sep 22, 2004
Technical 35-36 Ford Trunk Conversion Exterior Hinges? - The …
2024年5月30日 · Ok, after some research, I knew I have seen these type of hinges on a 36. They are on 36 Ford Club Cabriolets. Now, the question is were these special made for this car or did Henry Ford do what he usually did and use parts from other models like from the 36 Ford Humpback Trunk Hinge? Only the Hambers who REALLY know 35-36 Fords will know.
Technical Dropped axle in a 36 Ford - The Jalopy Journal
2013年10月14日 · The lower you go the closer the tie rods come to the bottom of the oil pan. I think 5 in. is too much for a 36 Ford due to fitment problems. Here's some general info: A 4 inch dropped axle results in a 2 in. drop. A stock reversed eye spring gives you an inch more drop. A Posie reversed eye super low spring will give you even more drop.
Technical 20 questions 36 ford 1/2 ton pickup - The Jalopy Journal
2022年4月3日 · 37 crank mechanism is different than 35/36 because the 37 windshield is vee’d vs flat for the 35/36. 36 car and truck crank mechanism is the same, I think. The hood center hinge contains a 1/4” full length steel rod that is captured at the radiator shell and cowl with the little bracket in your picture. It’s a piano hinge, essentially.
Technical - 36 Ford rear bones? | The H.A.M.B. - The Jalopy Journal
2016年12月19日 · I used 35-36 bones on my '40 PU chassis with a 66 F100 rear end (shortened 4-1/4" on one side) and used a 42-48 passenger car rear spring. The reason was, they are 1-1/2" shorter than a 35-40 spring, allowing more clearance at the rear shackle.
Hot Rods whats best headlites for '36 ford? - The Jalopy Journal
2019年9月16日 · The '36 bucket itself is the same thing as '35 car and '38-'39 truck. Only difference is the shorter stud and mounting hardware on the '36 bucket. I have the Drake reflectors with '36 car lenses and rings on my truck. You could use the flatter '35 car/'35-'39 truck lenses and rings on your '36.
serious lowering: rear of '36 Ford | The H.A.M.B. - The Jalopy Journal
2004年2月22日 · 2) Change to parallel leaves and open drive, and adjust the ride height further if necessary with lowering blocks. I think the old fart inside me will insist on keeping the Ford 3-speed and banjo rear end, so it can still stay largely early Ford. It …
Tire size & wheel offset for '36 Ford? | The H.A.M.B. - The Jalopy …
2013年5月2日 · I stuck with 16s on my '36 through several different versions, and settled on 600/front, 700/rear bias WWWs on 3/4 ton wide 5 wheels (couldn't find suitable whitewalls circa 2000): In hindsight, though, I believe that a lowered and/or chopped car looks better on 15s. I don't know the actual sizes on this car, but I think they're perfect:
Options for 36 Ford rear end? | The H.A.M.B. - The Jalopy Journal
2013年6月16日 · I am building a 36 ford 5 w. I am still rounding up parts and I am interested other people's opinions on what to build for the rear. I started with a nice bare frame and pretty good sheet metal. Here is what I have so far for a drivetrain. Front 4 drop axle with discs 66 283 new build dyno 290 hp 350 turbo or a 2004r