2024年8月29日 · Gas and Oil Home Heating Furnaces - Ruud Furnace - Hi Folks, 2 days ago I had a new Ruud R962V furnace and AC unit installed. The installer ran both heat and cooling before he left and all seemed fine. This morning I turned the heat up and everything work well but I notice 3 lights flashing through the bottom peep-hole,

2024年12月21日 · Gas and Oil Home Heating Furnaces - Ruud Silhouette II gas furnace has no flames. - I have a Ruud silhouette II gas furnace. Today I noticed it was about 58 degrees in my house. It is 10 degrees outside. Fahrenheit. I went to check the furnace and the flames are not present. The ignitor is electric and it gets very

2009年2月7日 · Goldstar and SeattlePioneer, thanks for your replies. The model # of the furnace is Ruud Silhouette II gas furnace ugph-ioeamer serial # ev5d302f409702077. I think that the fan that is coming on is the blower motor, it is very loud but I'm not to sure, how can I check. SeattlePioneer I don't know where the pressure switch is.

2009年11月26日 · Gas furnace goes through startup cycle, lights, good blue flames, runs 3or4 minutes, blower motor (squirrel cage) doesn't start. Unit shuts down. Model 1012-920A board shows green, another green and a third orange flashing. When unit shuts down board gives 3 green flashes on the second green LED. 3 greens continue until I unplug furnace.

2013年1月21日 · Gas and Oil Home Heating Furnaces - Ruud Silhouette just stopped working - Just got home from work and the furnace insn't working Ruud Silhouette model rcba-60896624 SER# m2494 gas forced air Induction draft motor starts: really not sure..makes a humming noise bust doesn't sound like a motor/blower running. power and

2015年1月20日 · Locating flame sensor on RUUD gas furnace Can anyone please help me with the problem I have on Rudd gas furnace model# UGDG-07NAMCR from 1990. Problem I'm having is after I set the thermostat in heat mode and set it at 73 wihile room temperature is 68, the inducer fan comes on for about 30 sec., then the glow-plug starts glowing for about 10sec ...

2018年3月18日 · Hi, 17yo Ruud model UGPJ 07EAUER nat gas upflow furnace with LUX TX9600a thermostat. Lately, I have noticed the exhaust blower cycle seems different. Checked it this AM when furnace lit at end of the nightly setback period. The exhaust blower is coming on, but the distribution blower is starting at the same time.

2011年12月3日 · Gas and Oil Home Heating Furnaces - Ruud furnace start up and short cycling - Model UGLH-07EAUER, Silohuett II, installed 1997 The furnace goes through the normal sequence of starting up but when it comes to the burners igniting, 98% of the time only the burner with the ignitor in front of it ignites. After about 8-10

2024年3月12日 · Humidifiers and Dehumidifiers - Ruud Furnace with AprilAire humidifier - How do you wire an AprilAire humidifier with a Honeywell Home RTH9585WF thermostat to a Ruud Super Quiet 80 Two Stage Furnace, so the thermostat controls the humidity and the furnace control board powers the humidifier?

2020年11月2日 · I am working with a Ruud furnace in which it has a problem with the heating system and it is that when I put it in the heating mode it turns on the turbine, then it lights the spark and lights the flame but when it works for some 5 seconds or less it goes out everything and I get a code on the control board indicating code # 10 which tells me that it is from "1HOUR …